Devices You Need to Set Up a New Bathtub
Devices You Need to Set Up a New Bathtub
Blog Article
The writer is making a few good points relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content directly below.
Setting up a bathtub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably difficult project. If the old bathtub is conveniently obtainable, the project can relocate quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will require a helper to leave the old bathtub and set in the brand-new one. Ensure you have certified on your own for the job and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will aid you mount a brand-new bath tub in your washroom if you have already bought a brand-new bathtub and do not need to change the setup of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Getting ready for the Installment
First of all, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to avoid strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its last placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather troublesome because of the restricted access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Using both wooden boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub up until the spirit level reviews level.
To install taps, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water system and inspect all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub should wait until the tub has actually been utilized at the very least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in area in between the tap and the sink. Secure the faucet in place with the supplier supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The former kind needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealant can crack fairly early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads about Installing A Bathtub, I imagined sharing that piece of content was necessary. Sharing is good. You never know, you might be doing someone a favor. Thanks so much for taking the time to read it.
Schedule Service Pickup
Report this page